INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Jugal Zugore
Country: Japan
Language: English (Spanish)
Genre: Sex
Published (Last): 25 November 2017
Pages: 93
PDF File Size: 3.38 Mb
ePub File Size: 18.95 Mb
ISBN: 734-9-41851-782-7
Downloads: 17310
Price: Free* [*Free Regsitration Required]
Uploader: Malagal

Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

A surface profile of mils microns is recommended. Dry bristle brushing will normally be adequate for accumulated dirt.

Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate.

Avoid using a mixture of application methods whenever possible.

With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Typically this would apply to C or D grade rusting in this standard.

For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Always mix a complete unit in the proportions supplied. Trowel or roller can be used for small areas. A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Further information is available from International Protective Coatings.

  MANUAL CHITARA INCEPATORI PDF

It is also possible to apply to damp surfaces in some circumstances.

Puddles, ponding and accumulations of water must be removed. Low or high temperatures may require specific application techniques to achieve maximum film build. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure.

Sagola or Air texture gun fitted with a mm nozzle. Once the unit has been mixed it must be used within the working pot life specified. Preferred application is by a suitable large tip hopper gun e.

If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS. Mouse over image to zoom. Accumulated dirt and soluble salts must be removed.

However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.

Please consult International Protective Coatings for alternative recommendations. Soluble salts should be removed by fresh water washing.

However, it can be used over suitably primed surfaces. Prior to paint application all surfaces should be assessed and treated in accordance with ISO Typical thicknesses will be between milsmicrons. Certification is for tanks greater than gallons Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS.

  FANSADOX COLLECTION BLACK VAN PDF

Consult International Protective Coatings for further details.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Varnish Hybrid Water base. Press and move to zoom. Do not thin more than allowed by local environmental legislation. Level of sheen and surface finish is dependent on application method.

Surface preparation The performance of this product will depend upon the degree of surface preparation. NSF Certification is for tanks greater than gallons Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.

INTERSEAL HS PLATINUM GREY MSDS Download

Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. The surface to be coated should be clean, dry and free from contamination. However, these phenomena are not detrimental to anti-corrosive performance.